Question#1
Hey Robert, I know I’ve seen this in your article before, but I can’t remember the answer. I hope you’re willing to revisit this once again. Just recently I’ve had a banging noise appear when I turn on the water in my house, both the hot and cold water. Can you help me figure out what this noise is and how to fix it, please? Javier H.
Answer #1
Javier, not a problem revisiting a question; I’m here to help. First thing you’ll want to do is to go to your local hardware store and buy a water pressure gauge, found in the plumbing department. This will just thread onto one of your exterior water bibs, or anywhere you have a water bib. Turn on the water, and read the gauge. According to the UPC (Uniform Plumbing Code), the pressure has to be 80 lbs. or less. The best thing to do is to set it at about 65 lbs. so that you have enough pressure for comfortable tasks in your home, but you also will save water. This is especially helpful in the drought we are in. If you have too much pressure, you’re introducing volume with pressure. The noticeable difference between 65 and 80 is virtually none. If you are somewhat handy, you can go to your PRV (pressure reducing valve) that is usually found on the side of your home, sometimes in the garage of newer homes, and use the set screw to make any adjustments. If you are not familiar with these things, call a plumber to do this for you. If you turn the set screw, you can watch the pressure change on the pressure gauge. Adjust accordingly, until you are near about 65 lbs. Most of the time when you’re getting these noises, the PRV has gone bad. In this case, the adjustment won’t work. Another possibility that I’ve seen happen is that kids have found this gadget and played with it (especially the Brockman brand because it is a knob versus a set screw), taking it out of adjustment. Either way, if the PRV is in good shape, the gauge will help you to make adjustments. Should you find the PRV to be bad, you can purchase a new one at the local hardware store. The Wilkins brand has the set screw which makes it more difficult for someone to randomly change the pressure. You’ll need to go to the ball valve and turn the water to your home off, and change this out like for like. It is very simple, they have a union on them – you’ll break the union and unscrew the old, reverse with the new. Remember to use Teflon plumbing tape (wrap this backwards, so that when you screw the PRV on, the tape stays in place), for the seal. Use the gauge to check the pressure and adjust on the new PRV, and this should solve all “hammering” noises. Good luck with this project.
Question #2
My name is Bonnie M. I’ve got a good sized fountain at my home and there is a lot of that white hard water stuff all over the stone and fountain. I chip away at it, I’ve used a pumice stone and I just can’t seem to get it all off and/or keep up with this. What can I do for this, is there an answer to this problem or do I have to live with it? I see other fountains that don’t have this, so I feel as though I’m missing a piece to the puzzle. Can you help?
Answer #2
Bonnie, get a hold of a pool man or anyone that does bead blasting. If you don’t have a recommendation, reach out to me and I will give you the name of someone that I trust. They use glass beads in a hopper with a high psi and this breaks the calcification off without damaging the stone or tile: this is very commonly used around pools. The glass beads will end up in your case on the ground or in the fountain, and they’ll use a recirculating pump with a net and literally vacuum up the glass beads. You can do this on a pool annually, this is what I do at my home. It almost makes the tiles look brand new again, and is very cost effective. Many hours of hard labor are saved by using this method, I highly recommend it.
Question #3
Robert, we have a patio on the back side of our home at the master bedroom. When it rains or we wash down, we get a leak below. I’ve used your suggestion and have done a water test to this area. There is a little piece of metal that goes from the deck through the patio wall, and then goes out. I got down there and can see where the metal is rotted. What is this thing called and how do I get this out of there, it looks like I’d have to break out the stucco – is that correct? It looks like a piece of gutter, though some sort of custom type piece. I’m pretty handy but I don’t want to ruin my home by not knowing how to tackle this. Do you know what this might be and how to repair it? Bob S.
Answer #3
Bob, what you’re looking at is a scupper. This is literally a vehicle for the water to get off of your decking. It’s obviously stuccoed and flashed with the decking system, integrated into the decking system. Unfortunately you’re going to have to break into the decking system, break out the stucco on the exterior wall and pull this scupper out. You’ll have to go to what we call a “tin knocker”, a sheet metal shop with your scupper, and have one fabricated. Make sure that you waterproof and reinstall in the reverse order of how you took this all out. There is an array of decking systems; you’ll have to figure out which you have. If you’re not familiar with these, be careful. Most are not compatible with one another, you need to have the same product that exists, for it to seal well and protect your property. If this is beyond your knowledge, I highly recommend that you call a professional, as water will travel and if this area is not sealed properly, you may have future interior damage to your home. You can send a photo to me and I can try to determine which system you have, make sure that it is a close up of the system as well as a broad view. There are many systems out there, and this is a very important step. Feel free to inquire further with me, and good luck.
Robert Lamoureux has 38 years of experience as a general contractor, with separate licenses in electrical and plumbing contracting. He owns IMS Construction Inc. in Valencia. His opinions are his own, not necessarily those of The Signal. Opinions expressed in this column are not meant to replace the recommendations of a qualified contractor after that contractor has made a thorough visual inspection. Email questions to Robert at [email protected].
