Question #1
I’m one of those handy guys similar to the ones who write in, and I’m in need of a little advice. At my home on each side of my garage there are, for lack of a better term, posts that are covered in stucco.
One of my upcoming chores that my wife would like done is to put that thin, flat brick on these posts. I’d like your advice because I’ve gotten mixed advice: Do I need to tear out the stucco, put the chicken wire up, build the stucco up and then put the brick on it? Or can I just put the brick facade on the stucco?
Some say yes and some say no. Steve W.
Answer #1
Steve, the answer is yes, as long as you score that stucco really well. You want at least minimally three-eighths-inch-wide score, so use a diamond blade and “rake” the stucco, putting a lot of these scores into it.
When we do stucco we put a scratch coat on and call it “raking.” When we then come back with our brown coat, the scratch coat allows the brown to adhere.
Your “raking” will serve as your scratch coat and allow your mortar to adhere to the stucco; then your pavers will stick. If you installed the pavers without raking, I guarantee that your pavers would fall off within months.
Make sure also that you hydrate your pavers prior to installation. Set them in water and allow them to absorb the moisture so that when you put them onto the mortar they won’t immediately soak up the moisture and create a less-than-perfect adhesion by drying out your mortar.
Take them out of the water, get most water off and then start setting them in the mortar beginning from the bottom. It’s a fun project — tedious but fun. Good luck.
Question #2
I live in a homeowners association in Stevenson Ranch. I saw the big article in The Signal about El Niño, which is why I’m writing. I have a fairly large deck and when it rains I get all of this water pooling in one corner that is about 1 inch deep.
With El Niño I’m afraid that I may get some flooding inside my unit, which is on the second floor. The little hole that is there to drain the water, which is about two inches by four inches, is way over on the other side of the deck from where the water pools.
I’ve contacted three companies and now I have three opinions on what to do about this: One says take the whole deck out and start over, which is incredibly expensive; another says to drill another hole and make some sort of opening so that the water can drain to the gutter outside, which means they’ll have to break through the stucco and redo the whole deck again; the third guy says to put some sort of concrete over it and then redo the surface.
I need some advice. Where do I start? Joan R.
Answer #2
Joan, if there is enough room between the deck and the sliding door itself so that you can build it up with a diamond lath, concrete and then redo the surface, this is probably the best way to go, in my opinion.
This is all contingent on what I think I’m seeing in the picture you sent. If the deck is in good condition, meaning no soft spots (if you do have soft spots, you really need to tear out the deck flooring and rebuild), then you can come in and just do an overlay of a new system, which will be the most economical option.
Walk your deck and if it feels stable on the whole deck, then you can move forward with this option.
Question #3
Boy, all of the articles in The Signal regarding El Niño and weather have me on high alert. I live in Sand Canyon and have an out building that has that rounded roof tile, and when I was out there I found that I have leaks.
I’ve searched Home Depot and everywhere I can think of and no one has this tile. What do I do? This is a huge roof and I have probably 50 pieces that need replacing.
Do I need to replace this whole roof? I’m kind of panicked. What do I do? Jim J.
Answer #3
Jim, go to a bone yard. Write me privately and I will send you a recommendation for one here in Santa Clarita and two or three out in the Valley. These are called “barrel tiles,” from what I can tell by the photo you submitted, and you can call the bone yards to inquire about their inventory.
This is a big roof and the paper looks really sun-beaten, so my best recommendation is for you to replace the paper before installing the replacement tiles. This is labor-intensive but it will save the building by creating a water-tight area.
The tile is brittle, so make sure that you never step on the crown of the tile. Always step in the valley (the indent). If they are old and brittle and you do step on the crown, they will crack just like crackers.
When you put the tiles back down, especially if they are brittle, I would not use a hammer. I would use a screw gun and be very careful how you bring the screws down.
I see that there is concrete missing at the crown in some areas; make sure to fill these areas and then, for aesthetics, you can use the same color primer or paint to camouflage the concrete. Good luck with your project.
Robert Lamoureux has 38 years of experience as a general contractor, with separate licenses in electrical and plumbing contracting. He owns IMS Construction Inc. in Valencia. His opinions are his own, not necessarily those of The Signal. Opinions expressed in this column are not meant to replace the recommendations of a qualified contractor after that contractor has made a thorough visual inspection. Email questions to Robert at [email protected].

