ArchiveSCV
the-signal.com. The Santa Clarita Valley Signal. Back to the collection.

· the-signal.com, Wayback capture

Your Home Improvements

Robert Lamoureux: Insulate garage door for heat relief

Hi Robert,

I have a metal roll-up double garage door that isn’t insulated and faces east. From sunrise to noon the door gets extremely hot from radiant heat. I think this heats my garage all day long.

Could I cut pieces of attic or wall insulation and fit them in the 12 panels to cool the door? If so, what kind if insulation would be best? If the insulation is two-sided which side faces the inside of the garage?

Thanks for your time,

Rich C.

Hi Rich,

I would not use insulation because it won’t hold. The door is constantly moving and vibrating and there is no way to properly affix it to the door. The best thing to do would be to contact an overhead garage door company and purchase a styrofoam board insulator. It comes with an adhesive so you can glue it to the door.

This change can make a significant difference inside the garage — which will also assist in the cooling of your house, especially if you have a second floor.

When the heat hits the garage door it radiates through the metal then rises inside the garage and travels up through the floors of your home and out the roof. The new insulation would also help protect your roof and paper.

Dear Robert,

I read your column every week and really enjoy it. I have a problem with a toilet. I have identical toilets in back-to-back bathrooms which appear to share the same vent. While one toilet flushes properly every time, the other has a two-flush cycle — the first flush just fills the bowl and swirls a bit — then the second flush is normal. The next time it is flushed it repeats this cycle.

This has become the norm and I am stumped as to why. I used your advice and bought a toilet auger, but the pipe seems to be clear. There are no leaks and everything seems to be working fine, except for this problem. This has been going on for a little more than a month now. Thank you very much,

Lee J.

Hi Lee,

It sounds like a bad toilet. Even if it’s relatively new, sometimes they ship from the factory defective. It’s not uncommon.

Another possibility is the jets inside the rim of the bowl are calcified and plugged up. Take a wire coat hanger and bend it into the shape of a check mark. Using a mirror, push the wire up inside and clean out each jet to see if that helps.

Augers are great to have on hand, but it is possible that there may be some partial obstruction. The auger may go in and out, but is actually passing over the blockage hidden in the bottom of the trap. Because it’s all porcelain and sealed, you cannot see the inner workings of the bowl.

I would first try to clean the jets which may give you better results. If not, a new toilet may be needed.

Hi Robert,

We recently hired a contractor to paint some metal window coverings at our home and we are concerned about the paint being sprayed on when it was 110 degrees last week. It looks like there are lines running through different sections of their work. Also, some areas are wet looking and others are not. Would the heat affect the quality of the painting and or the longevity? Sincerely,

S.R.

Hi S.R.

Yes, this would cause big problems. In extreme high heat, paint starts to dry as soon as it leaves the sprayer. Not only that, with the temperatures we had last week, metal surfaces are so hot that the partially dried paint would hit and dry instantly.

This would not allow for a strong bond and would probably cause flaking and/or peeling within six months to a year.

The lines and spots you’re referring to are indications the paint dried too fast or are the result of poor painting technique.

Lines usually indicate painting began in one direction, stopped, then continued from the other side. Painting with sprayers is an art form in itself. It requires the painter to make one continuous sweep from side to side, while keeping the gun perfectly perpendicular to the surface. If there is a wide panel, the painter must be able to move back and forth to lay down a nice, even coat.

This takes many hours of practice to do well. Some painters will pick a starting point and stand in the middle of the panel they are spraying. They just rotate the sprayer from left to right. The problem with this is when painting all the way to the left, the sprayer may be two feet away from the surface, but head on it’s only six inches away. This will give you dry — wet — dry. We call those holidays. It’s not a good look. High temperatures would only accentuate mistakes.

Hi Robert,

We had some stucco work done recently on our home. There are numerous windows, but on the side of the garage there is mostly wall surface. The stucco on that side looks like a patchwork quilt with a line separating one section from the other.

We are surprised because we hired a general contractor. What can be done to make it look right? Thank you,

May G.

Hi May,

Well, there are many people getting into areas that they shouldn’t be in because times are tough. Some profess to being a general contractor, therefore meaning you can do anything you want, right? It sounds like they are inexperienced.

A general contractor is basically a conductor. I know how to bring in all the instruments. I have the ability to bring everyone together and know how to make it work and orchestrate. Some contractors have specialty licenses. As an electrical contractor, I am proficient to be the electrician on that job; as the plumbing contractor, I am licensed for whatever plumbing may be necessary. So, just because somebody is a general contractor doesn’t necessarily mean they will provide you with a quality stucco job.

The line you are referring to is where they stopped. With stucco, you need to go from corner to corner. If you’re going to stop, do a complete wall and then stop. Don’t stop midway or you will see a line — unless you know how to feather.

To make it look right, have them come back out and sandblast and redo it — or feather it out.

We have designed a custom, full-color The Signal/Your Home Improvements T-shirt we will give you if we answer your question. The T-shirt is available to be picked up at our office.

Robert Lamoureux has 25 years experience as a general contractor, with separate licenses in electrical and plumbing contacting. He owns IMS Construction Inc. in Valencia. His opinions are his own, and not necessarily those of The Signal. Opinions expressed in this column are not meant to replace the recommendations of a qualified contractor, after that contractor has made a thorough visual inspection. Send your questions to [email protected].

← Back to 2010

About this record

How it was held, read and classified

Record details

Morris ID
33158
System
Morris section CMS (/section/…/article/… and /archives/…)
Reading copy
the-signal.com
Chosen by: only copy held. On this copy: words 1,186 (e-mail addresses counted as one token); reader comments 0 (counted, not reproduced here); images 0.
Extracted by
section_cms:articlebody_span
signal-extract/0.15 (2026-11-16)

Other copies

Held
None. The holding has this article from one host only.

How it was classified

Label
clearly-local
Judgment
A machine’s (recorded as machine), kept as one so it can be revisited.
Classifier
signal-localclass/0.7 (2026-11-12)
Local signals
  • text:valley_names [1 distinct/1 mentions: Valencia]
  • byline:named_writer_no_wire_credit [By Guest Commentary]
National signals
none fired
Scores
local 3, national 0