ArchiveSCV
the-signal.com. The Santa Clarita Valley Signal. Back to the collection.

· the-signal.com, Wayback capture

Your Home Improvements — Saturday November 17, 2007

Ask the Expert

Dear Mr. Lamoureux:

As a resident here in Valencia I have terrible water. Not only is it unpleasant to drink but it is hard on pipes and leaves spots on the shower door that my wife has a hard time cleaning. I am tired of buying bottled water and would like a whole house system to remedy that. I am currently using a water softener that I would like to get rid of. I was at the Business Expo last week and talked to Culligan, who have their "Filtr-Cleer" water filters and Rayne, who have the "Mulit-Media" Water Conditioning System with the "Filtrex Media." I have also talked to Life Source in the past. I don't want a reverse osmosis system due to the large amount of waste water that they discharge.

Can you help to sort through this maze and know which system will give me good tasting water at least as good as it was in the San Fernando Valley. Any Web sites that you know of would be greatly appreciated. Thank you.

Robert T.

Robert,

There are many water filtration systems to choose from. Reverse osmosis does use a lot of water - three to five gallons of waste for every gallon filtered - and is extremely slow.

I would first look for a system that was both UL listed (Underwriters Laboratories) for safety standards, and NSF approved (National Science Foundation) for sanitation standards.

Three of the higher rated units are the EcoWater system, the Wellness MG, and the Rhino EQ-300. All three are UL listed and NSF approved, and they each remove 99 percent of the chlorine present.

The EcoWater system costs about $3,000 and will remove particulates up to 10 microns. Based on the purchase price and the amount of gallons it will filter under normal conditions, it has a use cost of about $60 per month.

The Wellness MG costs about $6,000 and will remove particulates up to 5 microns. It also has a use cost of about $60 per month. The Rhino EQ-300 is currently on sale for $999. It removes particulates up to 5 microns, has a use cost of about $20 per month and is manufactured by Aquasana.

We called and spoke with the vice president of the company, Mr. Houston Tomasz. He said that as a service to the readers of the Ask the Expert column in The Signal, he would offer an additional discount of 20 percent, provide free shipping, and include a free six-pack of their glass decanters with any order - not just the whole house filter. Simply mention "Ask the Expert" to one of their operators at (866) No Bottle, or enter the word "expert" in the Promotion Code Box on the Web site listed below.

The Rhino EQ-300 uses a 3 step process:

1.) Filter out sediment with a 5 micron pre-filter.

2.) Remove chlorine with natural oxidation media.

3.) Enhance taste and clarity with bituminous charcoal.

Also, there is no wasted water or electrical required, three years between filter changes, virtually no maintenance, and seven gallon per minute flow rate means no loss of water pressure.

According to their Web site www.aquasana.com , their products have been voted a "Best Buy" by Consumer Digest magazine for 2003, 2004, 2005 and 2006.

Dear Robert,

My driveway is only five years old. We have little round chunks about one-quarter of an inch thick that are breaking off. It's starting to look really terrible. What is causing this? Is there anything we should be doing to prevent this? Thank you.

Olivia D.

Olivia,

That's called "spalding." What you've got is a bad mix of concrete. Too much "cream" came to the surface when they were working it, and it's the cream that's breaking and popping. You see this especially in colder climates. If the concrete was poured in really cold weather, the water will freeze inside the mix. If the water freezes, it breaks the surface, microscopically, and fatigues over the years. There are a couple of options for the repair. Either rip out the driveway and re-pour it, or add a new surface called an overlay. There are companies that come out and put a new surface on for you.

Hi Robert,

My attic access door is in our closet. It's just a piece of plywood that covers an opening in the ceiling that is difficult to get to. I'd like to install a new access door with a ladder in our hallway. Could you offer any tips before I get started? Many thanks.

Aaron J.

Aaron,

First pop a hole in the ceiling where you want to install the ladder. Then go up into the attic and see how the joists are situated where the ladder will land. The walls of your hallway are load-bearing so the joists will be running across the ceiling, from side to side, so the opening for access will be supporting part of that ceiling. You'll have to cut a minimum of three joists, depending on the type of ladder you install. Make sure these joists are nailed into the double top plate on both sides and I would also strap them with Simpson straps. After you cut the joists, frame it out with doublers - double the wood for the frame all the way around. For example, you probably have 2 inch x 8 inch joists. When you frame for the ladder, you are going to use (2) 2x8s on all four sides of the frame. This gives you plenty of meat to lag or bolt the ladder kit into. Ideally, you would want to sink your bolts into the ends of the original joists that you cut to make it even stronger.

You may want to call a contractor out for this. It is something you can do yourself if you are good with your hands and have an understanding of the structural components of your home. If so, it is important that you follow the framing instructions provided by the manufacturer to the letter. Never under any circumstance, no matter what trade you are working in, go against a manufacturers recommendations. They are the ones that spend millions of dollars devising a system, then test and re-test to make sure there is no liability.

Robert Lamoureux has 25 years' experience as a general contractor, with separate licenses in electrical and plumbing contacting. He owns IMS Construction Inc. in Valencia. His opinions are his own, and not necessarily those of The Signal. Opinions expressed in this column are not meant to replace the recommendations of a qualified contractor, after that contractor has made a thorough visual inspection.

Send your questions to [email protected] .

← Back to 2007

About this record

How it was held, read and classified

Record details

Morris ID
Not a Morris ID. This record is keyed ts-ds:51773.
System
displaystory pages (?module=displaystory)
Reading copy
the-signal.com
Chosen by: only copy held. On this copy: words 1,115 (e-mail addresses counted as one token); reader comments 0 (counted, not reproduced here); images 0.
Extracted by
displaystory:2007_font_head
signal-extract/0.15 (2026-11-16)

Other copies

Held
None. The holding has this article from one host only.

How it was classified

Label
clearly-local
Judgment
A machine’s (recorded as machine), kept as one so it can be revisited.
Classifier
signal-localclass/0.7 (2026-11-12)
Local signals
  • text:valley_names [1 distinct/2 mentions: Valencia]
  • byline:named_writer_no_wire_credit [By Robert Lamoureux]
National signals
none fired
Scores
local 3, national 0